United States - COVER,LIFE PRESERVE

Description

Added: May 02, 2019 12:58 pm

COVER, LIFE PRESERVER
{COVER ASSEMBLY, EXTERIOR (LPU-38/P)}
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR
SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE
SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS.  FOR LARGE
ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE
APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON
REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
MIL-STD-130N(1) DATED 16 NOV 2012.
IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
 REF AIR FORCE DWG 200316413
 BAE SYSTEMS AEROSPACE AND DEFENSE GROUP (54786)
 PHOENIX, AZ
 REFER TO AIR FORCE DRAWING 200316413 FOR MARKING
 REQUIREMENTS PER NOTES 10 AND 11. THE SIMULA PART NUMBER FOR THE COVER
ONLY SHALL BE MARKED ON THE "INSIDE" OF THE COVER. THE EXTERNAL MARKINGS
SHALL BE AS SPECIFIED IN NOTE 11 OF THE DRAWING. LEAVE THE "SERIAL
NUMBER" PART BLANK. THE SERIAL NUMBER WILL BE PUT ON BY THE FIELD UNITS
TO MATCH UP TO A SPECIFIC BLADDER.
THE APPROVED SOURCE(S) MUST MEET THE REQUIREMENTS OF
THE CURRENT REVISION OF THE SOURCE CONTROL DRAWING
OFFERORS NOT CITED AS APPROVED SOURCES IN THE
PURCHASE ORDER TEXT ARE REQUIRED TO
OBTAIN SOURCE APPROVAL FROM THE OEM. A COPY OF
THE SOURCE APPROVAL REQUEST, TECHNICAL DATA
PACKAGE OR CERTIFICATION OF PRIOR APPROVAL MUST
ALSO BE SUBMITTED TO DLA WITH THE OFFER.
 SIMULA PART NUMBER SHALL BE MARKED ON THE
 INSIDE OF THE COVER. THE EXTERIOR LABEL SHALL
 CONFORM TO REQUIREMENTS SPECIFIED IN NOTE 11.
CRITICAL ITEM - SOURCE INSPECTION REQUIRED.
DATA IS PROPRIETARY OR INSUFFICIENT FOR
COMPETITIVE PROCUREMENT
QUALITY ASSURANCE DATA
CRITICAL APPLICATION ITEM
Bae Systems Land  Armaments L.P. 54786 P/N 0115210-1
IAW BASIC DRAWING NR 98752 200316413
REVISION NR B   DTD 10/02/2003
PART PIECE NUMBER:

Opportunity closing date

08 May 2019

Value of contract

to be confirmed